XING2 3110 Cinelifter Motor

Our XING series NextGen motors have become popular after the initial release in 2018 and became the new standard on the market. Was it the curved shape or the internal damping ring to protect the bearing, or was it the higher quality NSK bearings coupled with a higher grade titanium alloy shaft? We've been copied and compared all these years, but now it's time to set a new standard again! We're finally ready to announce our predecessor the XING2!

The smooth, reliable and powerful XING motors were upgraded and we achieved an even higher standard in our manufactory as well as better performance than ever before. New center slotted N52H curved arc magnets were introduced to drastically reduce response time of the motor! Maybe the biggest bottleneck of our FPV flight controller is the motor due to it's translation delay of it braking and accelerating. XING2 motors offer faster response to translate your PID loop quicker and get that locked-in feeling you were always looking for!

Due to the high quality materials used and the durable joint of bell and shaft, we were able to reduce the magnet air gap and stator lamination to a minimum. The smaller the air gap is, the lower that reluctance and the higher the magnetic flux (which is the magnetic analog of current) causing more efficiency and higher power!

If you want to upgrade your Nazgul Evoque F6 V1 with the DJI O3 Air Unit read this:

- The FC (Flight Controller) to O3 VTX connector is different than the older Caddx Vista/Polar plug. You'll need to DIY.

- The RX (Receiver) position changed. V1 antenna length is 75mm, V2 is 220mm. You'll need to DIY.

- The XT60 plug was changed, you'll need to de-solder the V1 plug and install the V2 plug. Included in the frame kit.

- If you're going from F6X V1 to F6X V2 all motor wires will have the same length.

- If you're going from F6X V1 to F6D V2 the back motor wires need to be extended, since you change frame geometry.

- The Antenna TPU in the back comes in 2 Versions; One for the original single DJI VTX antenna, or one for the dual antenna setup. The kit includes a dual antenna TPU. 2x 5.8G LHCP antennas need to be installed.

- The Nazgul Evoque F6 V2 BNF comes with a new Anti Spark filter pre-installed. Please select the option to purchase separately; it's not included in the frame kit.

Our XING series NextGen motors have become popular after the initial release in 2018 and became the new standard on the market. Was it the curved shape or the internal damping ring to protect the bearing, or was it the higher quality NSK bearings coupled with a higher grade titanium alloy shaft? We've been copied and compared all these years, but now it's time to set a new standard again! We're finally ready to announce our predecessor the XING2!

The smooth, reliable and powerful XING motors were upgraded and we achieved an even higher standard in our manufactory as well as better performance than ever before. New center slotted N52H curved arc magnets were introduced to drastically reduce response time of the motor! Maybe the biggest bottleneck of our FPV flight controller is the motor due to it's translation delay of it braking and accelerating. XING2 motors offer faster response to translate your PID loop quicker and get that locked-in feeling you were always looking for!

Due to the high quality materials used and the durable joint of bell and shaft, we were able to reduce the magnet air gap and stator lamination to a minimum. The smaller the air gap is, the lower that reluctance and the higher the magnetic flux (which is the magnetic analog of current) causing more efficiency and higher power!

5mm titanium alloy shaft, our strongest prop shaft ever!

Crash resistant 7075 aluminum bell

Smooth and long-lasting NSK 11x5x5 bearings

Center slotted N52H curved arc magnets

XING O-ring bearing gap protection

Motor wires protector

Dynamically balanced

Designed for 7/8/9 inch Cinelifter.

December 13, 2022: New silicone inserts have been designed to replace the TPU ones，which are holding the 03 cam in the side panels. 

5mm titanium alloy shaft, our strongest prop shaft ever!

Crash resistant 7075 aluminum bell

Smooth and long-lasting NSK 11x5x5 bearings

Center slotted N52H curved arc magnets

XING O-ring bearing gap protection

Motor wires protector

Dynamically balanced

Designed for 7/8/9 inch Cinelifter.

KV: 900KV / 1250KV / 1600KV

Weight(included wire): 77g(900KV/1250KV) / 76.4g(1600KV)

Dimension: φ38.72*39.6mm

Interphase Resistance: 78mΩ / 43mΩ / 36mΩ

Input Volts: 33.6V (900KV)/ 4~6S(1250KV)/25.2V(1600KV)

Peak Current: 65.54A / 84.68A / 65.06A

Max Watt: 2143.8W / 1976.4W / 1550.4W

Mounting Holes: 19*19 φ3mm

Rotor Specifications: Unibell

Shaft Diameter: 5mm

Shaft Protruding Length: 15mm

Lead: 260mm/18AWG

Magnet: N52H Curved

Configuration: 12N14P

Bearing Type: NSK

Bearing Specification: φ11*φ5*5

Winding: Single Strand copper winding

Product Name: Evoque F6 V2 Frame Kit

Frame wheelbase: 255mm (Squashed X) / 262 mm (DeadCat)

Frame Dimension: L196*W164*H36 mm (Squashed X) / L209*W162*H36 mm (DeadCat)

Frame Body Dimension: 36mm

Arm Thickness: 6mm

Bottom Plate Thickness: 3mm

Top Plate Thickness: 2mm

Upper Plate Thickness: 3mm

Camera Plate Thickness: 3mm

Max Flight Stack Height: 22mm

Max VTX Height: 23mm

FC Mounting: 20*20/Φ3mm

Motor Mounting: 16*16/Φ3mm

VTX Mounting:  25.5*25.5 φ1.6mm

Weight: 252g/256g

KV: 900KV / 1250KV / 1600KV

Weight(included wire): 77g(900KV/1250KV) / 76.4g(1600KV)

Dimension: φ38.72*39.6mm

Interphase Resistance: 78mΩ / 43mΩ / 36mΩ

Input Volts: 33.6V (900KV)/ 4~6S(1250KV)/25.2V(1600KV)

Peak Current: 65.54A / 84.68A / 65.06A

Max Watt: 2143.8W / 1976.4W / 1550.4W

Mounting Holes: 19*19 φ3mm

Rotor Specifications: Unibell

Shaft Diameter: 5mm

Shaft Protruding Length: 15mm

Lead: 260mm/18AWG

Magnet: N52H Curved

Configuration: 12N14P

Bearing Type: NSK

Bearing Specification: φ11*φ5*5

Winding: Single Strand copper winding

1 x XING2 3110 Brushless Motor

4 x M3x10 screws

1 x M5 Flange Nut

1 x Evoque F6 V2 Frame Kit

1 x O3 Air Unit Heatsink

2 x O3 IPEX to RP-SMA Antenna Pigtails

1 x O3 Dual Antenna TPU

1 x GoPro TPU Base Mount

1 x Screw Bag

4 x TPU Armguard

1 x Front Bumper TPU

1 x Rear Bumper TPU

2 x Anti-slip Battery Pad

2 x Battery Strap (20*250mm)

1 x Battery Strap(20*250mm)

1 x XING2 3110 Brushless Motor

4 x M3x10 screws

1 x M5 Flange Nut